MOROSO PERFORMANCE

Sort By:  
MOROSO 3-VANE VACUUM PUMP; ORIGINAL DESIGN (22640)
22640Original Design 3-Vane Vacuum Pump

  • Versatile Billet aluminum design
  • Engineered vane material for improved efficiency and wear
  • Completely rebuildable in 15 minutes
  • Mounting bracket not included
  • 4.150" O.D. body, 5.050" from back of pump to pulley mounting flange


Part #AVAILABLE OPTIONS
22645Vacuum Pump Vane Kit, 3 Vane


Part #MOUNTING BRACKETS
63909Mounting Bracket, Big Block Ford, Driver or Passenger cylinder heads
63910Mounting Bracket, All Engines, With a motorplate or Small and Big Block Chevy with Driver/passenger cylinder heads
63911Mounting Bracket, Small Block Ford, Driver or Passenger cylinder heads
63912Mounting Bracket, Big Block Chrysler, Driver side of engine block
63921Mounting Bracket, Ford 4.6/5.4, OEM, Power Steering Pump Location
63922Mounting Bracket, GM LS,Driver side cylinder head
63923Mounting Bracket, GM LS,Passenger side cylinder head


Part #REPLACEMENT PARTS
97641Replacement Fittings, -12AN
97180Rebuild Kit, Original Design Pumps
22626Replacement Fittings, -16AN

GETTING THE MOST PERFORMANCE FROM YOUR VACUUM PUMPS

Moroso Vacuum Pump Nos. 22640 and 22641 can be driven no faster than 6500 RPM. The Moroso Vacuum Pump Nos. 22642 and ­­­22643 can be driven as high as 8000 RPM. Moroso offers many ratio options for two reasons. First, by spinning the pump fast enough to achieve the desired vacuum at staging RPM is critical to getting the most performance from your vacuum system. Typically the amount of vacuum it makes below your staging RPM is not as important as it is when you are under a load and ready to make your run.

Second, with engines that either run on alcohol, are supercharged or turbocharged, having the pump spin to maximum RPM to maintain vacuum is necessary in some cases. This will decrease the life of the pump, but will achieve the desired results.

$461.95
MOROSO SBC ALUMINUM RACE PAN (21234)
21234Fits: Pre-1985 Engine Blocks including Dart and Merlin



Aluminum, Wet Sump, 8 Quart Capacity, 8-1/4" deep

Engine Application: Pre-1985 Engine Blocks including Dart and Merlin

Fits: Super Stock/Bracket Cars, Dragsters, Roadsters or Body Cars with wet sump oil systems

  • Aluminum, fully fabricated oil pan accepts 4.25" strokes with steel rods
  • Double kick-out design ensures large stroke clearance, wide main cap clearance and maximum horsepower
  • Billet end seals ensure consistent sealing surface to billet front covers and rear main caps
  • For use with 168-tooth flywheel combination
  • Solid lourvered tray for maximum power and oil control
  • Features O-ring magnetic drain plug, two 1⁄2" N.P.T. drain backs and dipstick bung



Part #RECOMMENDED PICKUPS
24170Fits: Moroso SBC Race Pump No. 22101 or M55 style pump
24350Fits: Moroso SBC HV Race Pump No. 22111 or M55HV style pump



Part #OIL PUMP/PICKUP PACKAGE
22124Moroso Standard Volume Package
22134Moroso High Volume Package
22171Moroso Billet Aluminum Oil Pump



Part #AVAILABLE OIL PAN OPTION
25970Universal Dipstick Kit
25971Universal Dipstick Kit, Braided Stainless Flex Tube
25973Universal Dipstick Kit,Twist Lock
38385Billet Nose Oil Pan Stud Kit
93150Oil Pan Gasket, Pre-’85 block with a 2 piece rear main seal

$608.95
MOROSO SBC VACUUM PUMP & OIL PUMP DRIVE KIT (63859)
63859Oil Pump and Vacuum Pump Drive Kit, Small Block Chevy, Long

  • Bolts to balancer–balancer does not need to be drilled like older designs
  • Pulleys are hard coat anodized and mandrel is black oxide for exceptional strength and extended service life
  • Kits include: one-piece, forged steel drive mandrel, 4" V-belt pulley for alternator, 2-1⁄2" V-belt pulley for vacuum pump, 1" (16 tooth) Gilmer pulley for external oil pump, guide plates, assorted spacers, belt guides and hardware
Part #AVAILIBLE OPTIONS
63861Drive Mandrel Spacer Kit, SBC, for 1/4" Thick Crank Trigger Wheels
$226.95
MOROSO VACUUM PUMP MOUNTING BRACKET (63910)

63910Vacuum Pumps to SBC or BBC Cylinder Heads or any Engine using a Motorplate

  • Vacuum Pump Mounting Bracket, Mounts Moroso Part Nos. 22640 and 22641 Original Design Vacuum Pumps to driver or passenger side cylinder heads on a SBC or BBC or to any engine using a front Motorplate
  • Mounts to driver or passenger side cylinder heads on a SBC or BBC
  • Any engine that has a front Motorplate
  • Bracket is machined from Billet Aluminum
  • Has a black anodized finish for looks and durability
$58.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, BBC, OVER VC/POINTS

Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, BBC, Under Header/HEI

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
$151.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, SBC, OVER VC/HEI (73607)

Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, SBC, Under Header/HEI

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
$146.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, GM LS, MEDIUM (73537)

Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, GM LS Series, Coil-on Plug Boots, MEDIUM

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
$114.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, GM LS, REMOTE, BLACK (73845)

Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, GM LS Series, Coil-on Plug Boots, REMOTE

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
  • AVAILABLE IN BLACK ONLY
$114.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, SBC, UNDER HEADER/HEI (73607)

3607Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, SBC, Under Header/HEI

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
$146.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, SBC, OVER VC/POINTS (73607)

Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, SBC, Under Header/HEI

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
$146.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, GM LS, SHORT (73535)

Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, GM LS Series, Coil-on Plug Boots, Short

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
$114.95
MOROSO BBC ALUMINUM RACE PAN (20485)
20485Fits: Competition Eliminator, Super Gas, Super Comp and Bracket cars. Installation may require modifications to cross-member check dimensions carefully before ordering. BBC GEN IV ALUMINIUM OIL PAN, 8.00" DEEP, WITH DIVIDED TRAY



Wet Sump, 6 Quart Capacity, w/ Standard Volume Pump, 7 Quart Capacity w/ High Volume Pump, 8" Deep

Engine Application: Mark IV style (except Gen V and Gen VI)

Fits: Fits: Competition Eliminator, Super Gas, Super Comp and Bracket cars. Installation may require modifications to cross-member; check dimensions carefully before ordering

  • Fully fabricated aluminum with billet end seals to ensure consistent sealing surface to billet front covers and rear main caps
  • Utilizes “race” pan rail bolt pattern, recommended oil pan gasket, Fel Pro Part No. 1863
  • Double kick-out design ensures up to 4.75” stroke with aluminum rods, wide main cap clearance and maximum horsepower
  • Solid louvered windage tray w/main cap partitions for maximum power and oil control
  • Sump design works with Moroso spur gear and gerotor billet oil pumps
  • Features two O-ring magnetic drain plugs, two –8AN drain backs, alternator notch
  • For use with 168-tooth flywheel combination
  • Pump adjustment bung with plug



Part #RECOMMENDED PICKUPS
24440Fits: Moroso BBC Race Pump Nos. 22150, 22160, 22162 or M77/M77HV style pump
24441*Fits: Moroso BBC Race Pump Nos. 22150, 22160, 22162 or M77/M77HV style pump



Part #OIL PUMP/PICKUP PACKAGE
22175Moroso Standard Volume Package
22185Moroso High Volume Package
22186*Moroso High Volume Package/Front Style Offset Pickup
22187Moroso High Volume Package with Windage Shield
22163Moroso Billet Aluminum Oil Pump, BBC, High Volume
22164Moroso Billet Aluminum Oil Pump, BBC, Standard Volume
22167Moroso Billet Aluminum High Volume Oil Pump

*Offset to middle of sump for more consistent oil pressure under braking

Part #AVAILABLE OIL PAN OPTION
25970Universal Dipstick Kit
25971Universal Dipstick Kit, Braided Stainless Flex Tube
25973Universal Dipstick Kit, Twist Lock
62255Wrench, Oil Pan T-Handle, 1⁄2", 6 PT
38361Oil Pan Fastener Kit, BBC Race Pans

$608.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, SBC, UNDER HEADER/POINTS (73605)

73605Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, SBC, Under Header/HEI

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
$146.95
MOROSO BBC BILLET OIL PUMP
22163Oil Pump, Billet Aluminum, BBC, High Volume

  • 6061-T6 billet housing with 3 times larger mounting boss area to prevent breaking
  • Weights 1 lb. less than stock oil pump with pickup
  • Inlet area is increased to prevent cavitation
  • Thrust bearing assembly increases housing and gear life due to drive shaft axial forces on the drive gear
  • Pump will clear 4-3/4" stroke with most steel rods
  • Engineered to fit 8" deep oil pans
  • Patent No. 5,810,571

$384.95
MOROSO BBC VACUUM PUMP & OIL PUMP DRIVE KIT (CK0013)

63849Oil Pump and Vacuum Pump Drive Kit, Big Block Chevy, Long

  • Bolts to balancer–balancer does not need to be drilled like older designs
  • Pulleys are hard coat anodized and mandrel is black oxide for exceptional strength and extended service life
  • Kits include: one-piece, forged steel drive mandrel, 4" V-belt pulley for alternator, 2-1⁄2" V-belt pulley for vacuum pump, 1" (16 tooth) Gilmer pulley for external oil pump, guide plates, assorted spacers, belt guides and hardware

*For SBC 1⁄4" thick crank trigger wheels, use part No. 63861 Drive Mandrel Spacer Kit (see below)
**Centers off of I.D. of Balancer, via supplied crankbolt washer

$234.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, BBC, UNDER HEADER/HEI

73616Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, BBC, Under Header/HEI

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
$151.95
MOROSO VACUUM PUMP KIT FOR BBC (22640K2)

Orignal Design Vacuum Pumps & Kits

Pump Features:

  • Versatile Billet aluminum design
  • Engineered vane material for improved efficiency and wear
  • Completely rebuildable in 15 minutes
  • Mounting brackets for different applications
  • Dimensions: 4.150" O.D., 5.050" back of pump to pulley mounting flange

Kit Includes:

  • Moroso 3-Vane Vacuum Pump
  • Moroso Vacuum Pump Mounting Bracket
  • Moroso Vacuum Pump Pulley
  • Moroso Drive Mandrel
  • Moroso Vacuum Pump Vented Inlet Fitting
  • Moroso AN Radius Pump Fitting
  • Moroso Straight Hose End Fittings
  • Moroso 90° Swivel Hose End Fittings
  • Moroso Stainless Braided Hose
$1,020.00
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, BBC, OVER VC/HEI

Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, BBC, Under Header/HEI

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
$151.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, GM LS, COIL ON VC (73846)

Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, GM LS Series, Coil-on Plug Boots, VC

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
  • AVAILABLE IN BLACK ONLY
$123.95
MOROSO ULTRA 40 CUSTOM FIT SLEEVED WIRE SET, BBC, UNDER HEADER/POINTS

73616Ultra 40 Custom Fit Wire Set, Blue Wire, Sleeved, BBC, Under Header/HEI

Exterior sleeving offers improved dielectric strength for added resistance to outside pulses while electrical protecting wire against heat, chafing and contaminants

  • 8.65mm diameter wire with 40 ohms of resistance per foot
  • Sleeving adds extra dielectric strength which is wire’s ability to not be affected by outside electrical pulses
  • Sleeving extends spark plug wire life and protects against exhaust header heat, chaffing and contaminants
  • Complete, ready to install sets available for specific engines
$151.95
Per Page      1 - 20 of 27